EE 330 Lecture 2026 11 05 Ch7 Amp#2
Overview
The lecture develops biasing and small-signal analysis for common-source MOSFET and common-emitter BJT amplifiers, emphasizing that the DC operating point must leave room for an undistorted AC swing. Worked examples calculate MOSFET bias current, output range, and gain, then BJT bias, exponential base-emitter voltage, and gain; the lecture also introduces input/output resistance, transistor switching limits, and the effect of MOSFET output resistance.
Key takeaways
- The MOSFET example’s Q point is VD = 0.4 V, with VOV = 0.2 V setting the lower saturation boundary; the resulting maximum symmetrical output is only 0.2 V peak.
- For the common-source example, gm = 0.8 mA/V and RD = 17.5 kΩ produce an idealized voltage gain of about −14 V/V.
- For the BJT example, a 1 mA collector current with IS = 10⁻¹⁵ A and VT = 25 mV requires VBE ≈ 0.691 V; gm = 40 mA/V and RC = 6.8 kΩ give gain ≈ −272 V/V.
- The lecture’s stated 1.56 V output peak for a 5 mV input conflicts with its stated gain: 272 × 5 mV is 1.36 V, so the output amplitude should be checked before using it.
- Adding MOSFET output resistance changes the effective drain load from RD to RD ∥ ro and reduces gain magnitude to gm(RD ∥ ro).
- A 0.7 V BJT base-emitter drop is an approximate DC shortcut; the exponential current law is needed to calculate how VBE changes with collector current.
Chapters
- An AC signal rides on the transistor’s DC operating voltage, so the bias point determines how far the output can move before clipping.
- For a MOSFET amplifier, the output cannot fall below the voltage needed to maintain saturation, and it cannot rise above the supply.
- Biasing near the midpoint of the available output range allows the largest symmetrical signal swing.
- The common-source example uses VDD = 1.8 V, RD = 17.5 kΩ, K = 0.4 mA/V², W/L = 10, VGS = 0.6 V, and VT = 0.4 V.
- The overdrive voltage is VOV = VGS − VT = 0.2 V; the saturation-current model gives ID = 0.08 mA.
- The drain DC voltage is VD = VDD − IDRD = 0.4 V.
- The MOSFET must maintain VDS ≥ VOV = 0.2 V to remain in saturation, setting the lower output limit.
- With VD = 0.4 V, the lower-side headroom is 0.2 V, less than the roughly 1.4 V available toward VDD = 1.8 V.
- The largest symmetrical output is therefore 0.2 V peak, spanning 0.4 V total from 0.2 V to 0.6 V.
- In the AC equivalent circuit, the DC supply is treated as AC ground and the MOSFET is represented by its controlled current source gmVGS.
- With the source grounded and RD at the drain, the output is vout = −gmRDvgs, so Av = −gmRD.
- Using gm = K(W/L)VOV = 0.8 mA/V and RD = 17.5 kΩ gives Av ≈ −14 V/V, with inversion indicated by the negative sign.
- An ideal MOSFET gate draws zero small-signal current, so its input resistance is infinite in this model.
- To find output resistance, set the independent input voltage to zero; this makes the controlled current source zero.
- With channel output resistance omitted, the resistance seen at the drain is RD = 17.5 kΩ.
- The MOSFET load-line relationship is VDS = VDD − IDRD, while the saturation current follows ID = ½K(W/L)(VGS − VT)².
- The operating point, or Q point, is the DC location about which the AC signal varies; the output waveform must remain within the transistor’s operating limits.
- The gate signal must remain above VT to avoid cutoff, and the drain signal must stay above VOV to preserve saturation.
- The BJT small-signal model uses a controlled collector current gmVBE and a base-emitter resistance rπ.
- The model parameters are gm = IC/VT and rπ = β/gm, where VT is the thermal voltage and β is the transistor current gain.
- For the common-emitter circuit with emitter grounded, the voltage gain is Av = −gmRC.
- The example specifies VCC = 10 V, RC = 6.8 kΩ, IS = 10⁻¹⁵ A, and a target VCE = 3.2 V.
- Since the emitter is grounded, IC = (VCC − VCE)/RC = 1 mA.
- Using IC = IS exp(VBE/VT) with VT = 25 mV gives VBE = VT ln(IC/IS) ≈ 0.691 V.
- At IC = 1 mA, gm = IC/VT = 40 mA/V; with RC = 6.8 kΩ, the calculated gain is approximately −272 V/V.
- A 5 mV peak input therefore corresponds to a 1.36 V peak output by direct multiplication; the lecture states 1.56 V, which does not match −272 × 5 mV.
- The output is centered on the 3.2 V collector DC level, and its negative excursion must be checked against the saturation boundary.
- Using the lecture’s edge-of-saturation value VCE = 0.3 V, the collector current limit is IC = (10 − 0.3)/6.8 kΩ, about 1.43 mA.
- The corresponding base-emitter voltage follows from VBE = VT ln(IC/IS), allowing the required input-bias increase to be calculated relative to 0.691 V.
- For operation within 1% of cutoff, VCE = 0.99VCC = 9.9 V; the load-line equation gives IC = (10 − 9.9)/6.8 kΩ, about 14.7 μA.
- For the BJT load line, VCE = VCC − ICRC; zero collector current places VCE at VCC, while increasing current drives VCE toward saturation.
- A bias point near cutoff or deep saturation leaves little room for a clean signal in one direction.
- The lecture compares transistor output curves and load-line limits to motivate choosing an interior operating point for linear amplification.
- At cutoff, ID or IC is approximately zero and the output node rises toward its supply voltage.
- In the on state, current is high and the output voltage is low but not zero; the lecture cites about 0.2 V for a BJT and a current-dependent drop for a MOSFET.
- MOSFETs and BJTs can act as fast electronic switches, but unlike an ideal closed mechanical switch they retain a voltage drop when conducting.
- Channel-length modulation makes MOSFET drain current vary with drain voltage, so an AC signal can also shift the transistor’s current and operating point.
- The small-signal model includes output resistance ro, approximately VA/ID or 1/(λID).
- The drain load becomes RD ∥ ro, changing the gain to Av = −gm(RD ∥ ro), whose magnitude is lower than −gmRD.
- The 0.7 V base-emitter value is a convenient approximation for initial DC analysis, not an exact fixed voltage.
- For more precise current and bias calculations, use IC = IS exp(VBE/VT) and its logarithmic inverse.
- Small changes around roughly 0.69 V can produce substantial collector-current changes, which is why the exponential model matters in small-signal analysis.
Transcript excerpt
0:03 So last lecture we derived the the small signal equivalent circuit of both MOSFET and BJT. So today we're going to go into the example of Of course we we had a we had example quite a complex example. I was using that to show you guys how the process can be established any complex problem But today we can go through some more say solve problems so that we can see how we do that. So before I go to the example, so let's
0:50 look at So one of the important procedure in designing amplifier is to do the biasing because our AC signal is applied on top of a DC signal. So yesterday I drew a couple of figures, something like for example, if you have a DC coming and that's pure DC, but then you have AC coming, you you have that AC superposition like a super posed onto the DC signal. Right? And then in order to get the AC
1:37 back, of course we need to do filtering. We filter out the DC signal we get Uh because this AC is sitting on top of a DC signal, you can imagine that if that DC is not designed properly, what's going to happen is that when your AC enlarges, you're going to get a clip. Now example will look like this. Let's say this is your DC and you got an AC signal. So what happens is that if you if you got a um a DC which is too small, then you you have a superposition on of AC signal on top of the DC. You see what happens? Only the top
2:24 portion is going to be uh valid. The bottom uh part of the waveform is cut off because there's nothing you can get
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Wireless Power Transfer.