ECircuits-Lec11-2026
Overview
The lecture first explains how to estimate a circuit’s Thevenin output resistance by measuring its output with finite loads, then develops the first-order frequency response model for a nonideal op amp. It connects parasitic RC networks to the pole frequency, the 3 dB bandwidth, magnitude and phase roll-off, and the approximate gain-bandwidth product for a single-pole system.
Key takeaways
- A single loaded-voltage measurement cannot determine both Thevenin voltage and output resistance; use two distinct load resistances, or measure the open-circuit voltage first.
- Once Vth is known, the load that produces Vout = Vth/2 equals the circuit’s Thevenin output resistance.
- A first-order RC pole occurs at ωp = 1/RC, or fp = 1/(2πRC); the response magnitude is 1/√2 of its low-frequency value at that frequency.
- A single-pole op amp has an approximate −20 dB-per-decade roll-off above its pole, with gain-frequency product approximately constant in that region.
- Each additional pole contributes roughly another −20 dB per decade, so the single-pole gain-bandwidth approximation should not be applied unchanged to higher-order systems.
- For a first-order pole, phase shifts from approximately 0° below the pole to −45° at the pole and approaches −90° at high frequencies.
Chapters
- The lab asks students to measure output voltage with RL = 100 ohms and compare it with the open-circuit case, RL = infinity.
- For a Thevenin source, the load voltage is Vout = Vth × RL / (RL + Rout), so a finite, nonzero load reveals the effect of Rout.
- One loaded-voltage measurement alone leaves both Vth and Rout unknown; measurements with two different RL values provide two equations to solve for them.
- If Vth is known from an open-circuit measurement, vary RL until the output is Vth/2; at that point RL equals Rout.
- For the lab procedure, replace the existing RL with 100 ohms rather than connecting an additional load alongside it.
- Students may use the Canvas report template or another format; including the procedure, results, and relevant images helps the TA evaluate the work.
- The in-lab document is due September 18 at 11:59 p.m.; the lecture advises submitting by the end of the week.
- Unlike an ideal op amp with infinite bandwidth, a practical op amp does not maintain the same response at frequencies such as 60 Hz and 1 THz.
- Breadboards, PCBs, wires, and nearby conductors introduce parasitic resistance and capacitance that can form RC networks.
- Bandwidth describes the range over which a circuit behaves as expected, including maintaining its intended gain.
- For a resistor and capacitor in series, the capacitor impedance is 1/(sC), and voltage division gives the low-pass transfer function H(s) = 1/(1 + sRC).
- The circuit has a pole at s = -1/RC, with angular pole frequency ωp = 1/RC and time constant τ = RC.
- Since ω = 2πf, the corresponding pole frequency in hertz is fp = 1/(2πRC).
- The op amp’s nonzero output resistance Rout and parasitic output capacitance form an RC network that attenuates high-frequency output signals.
- A first-order low-pass response can be written as H(jω) = 1/(1 + jω/ωp), or equivalently 1/(1 + jf/fp).
- At frequencies far below fp, the output approaches its low-frequency value; at very high frequencies, the response approaches zero.
- At f = fp, the magnitude of a first-order response is 1/√2 of its low-frequency value, corresponding to half power and a 3 dB drop.
- For an op amp with low-frequency gain A0, the gain at fp is A0/√2; A0 is also called the DC or low-frequency gain.
- A pole is a value of s that makes the transfer-function denominator zero; with multiple poles, the dominant pole determines the bandwidth behavior.
- For one pole, gain remains approximately A0 well below fp and falls approximately in proportion to 1/f well above fp.
- The high-frequency asymptote has a slope of −20 dB per decade: increasing frequency tenfold reduces gain by about tenfold.
- Beyond the pole, gain multiplied by frequency is approximately constant, a relationship used to understand bandwidth extension under negative feedback.
- A 1 pF parasitic capacitor with a 1 kΩ resistance gives a pole near 160 MHz; increasing capacitance to 1 nF lowers it to about 160 kHz.
- For the transfer function 1/(1 + jf/fp), the phase is −tan⁻¹(f/fp).
- The phase is approximately 0° well below fp, −45° at fp, and approaches −90° far above fp.
- Unlike the magnitude’s straight-line Bode approximation, phase does not change by a fixed number of degrees per decade because the arctangent function is nonlinear.
- Unity-gain frequency is where the amplifier’s gain reaches 1, or 0 dB; for a single-pole op amp, it is approximately the low-frequency gain multiplied by the pole bandwidth.
- Each additional pole adds roughly −20 dB per decade of magnitude roll-off: two poles give −40 dB per decade, and three give −60 dB per decade.
- The simple gain-bandwidth product relationship applies to the first-order, single-pole case and does not directly describe higher-order systems.
- Recorded lectures are linked from a pinned GroupMe message rather than Canvas because the recordings are informal and not officially required.
- The take-home test will be posted on Canvas, with an expected submission window of about one week to ten days.
- The lecture closes by directing students to earlier recorded material for missed homework discussion and inviting questions about signal analysis.
Transcript excerpt
0:00 Right. So, >> in progress. [clears throat] >> Okay. So, let's get started. Uh, of course, we have our lab one going on uh this week and I guess some of you had asked a question on the group me chat. I would like to uh clarify that first and then we can go into the discussions for today. Um I think the question was related to part two where you have this particular circuitry and then you have some sort of RL resistance connected to it and the main question was for part B4 where we are asked to use an RL of 100 ohms to measure VO and compare this value when RL is equal to
0:47 infinite. So the idea here is that as you apply different values of RL so this RL resistance this is something that is in your code and in measurements by changing RL you'll get an idea about what is the R out you have for your circuit and why is that that is just because of the simple concept of voltage division that if I have a voltage source let's say some sort of aine equivalent voltage source which models this particular circuit and then you have a particular R let's say let's just call it R and then I'm connecting RL over here. So the idea is that the voltage that you'll see across RL that is the only observable you have. So you're
1:34 observing the voltage across RL and that voltage if this voltage is V the voltage across RL would be V * RL / RL + RO. Now of course if RL is infinitely large then this voltage is the full voltage V because RO doesn't matter but you do not get any information about RO as well. If
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, WISE Lab - UF ECE.