EE 2115 - Lec 06 - 2026_09_04
Overview
Hiren Trada explains how to analyze voltage-resistor-diode circuits with the constant-voltage-drop (CVD) model and compare it with the ideal-diode model, using 0.7 V as the silicon diode turn-on threshold. He applies the models to positive, negative, double-sided, and biased limiters, then derives voltage-transfer characteristics and half-wave rectifier outputs by changing where the output is measured.
Key takeaways
- For a silicon diode in the CVD model, assume a 0.7 V forward drop; an ideal diode instead turns on as soon as its anode is above its cathode.
- A reliable diode-analysis method is to assume the diode state, solve the reduced resistor-source circuit, then verify that the calculated diode voltage and current support the assumption.
- A positive limiter measured across the diode follows Vin until about 0.7 V, then clamps near 0.7 V; reversing the diode creates the corresponding negative clamp.
- A biased limiter shifts its clipping threshold by the added DC source; the positive threshold in the illustrated configuration is V0 + 0.7 V.
- A positive half-wave rectifier measured across its resistor outputs zero below the 0.7 V turn-on threshold and approximately Vin - 0.7 V above it; reversing the diode selects the negative half-cycle.
- Limiter and rectifier circuits can share the same VRD components and wiring; the output measurement point distinguishes them, across the diode for limiting and across the resistor for rectification.
Chapters
- Lecture objectives cover CVD circuit analysis and voltage-transfer characteristics for limiter and rectifier circuits.
- VRD circuits can combine DC sources, AC waveforms, resistors, and diodes; AC examples include sine, square, triangular, and sawtooth waves.
- Use Thevenin's theorem to reduce the source and resistor network to one equivalent source and one resistance, while analyzing diodes separately.
- Set the diode voltage reference with positive at the anode and negative at the cathode, then determine polarity and current direction.
- The ideal diode turns on when the anode exceeds the cathode, corresponding to VD greater than 0 V.
- The CVD model uses a 0.7 V forward drop: a forward voltage below 0.7 V leaves the diode off, while a higher voltage turns it on.
- Assume an on or off state, solve the circuit, and check whether the resulting diode voltage and current agree with that assumption.
- A resistor conducts in either direction, while a diode conducts only when forward biased.
- For a conducting CVD diode in series with resistance R, the current is approximately (VS - 0.7 V) / R.
- During the reverse-biased half-cycle, the diode current is approximately zero.
- A series resistor and diode have the same electrical behavior regardless of drawing order, but measuring across the diode or resistor gives different outputs.
- A positive limiter takes its output across the diode and clamps positive input once Vin exceeds about 0.7 V in the CVD model.
- With the diode off, no current flows through the resistor, so Vout equals Vin; when it turns on, Vout remains near 0.7 V.
- The VTC plots Vout against Vin and follows the input below the clamp threshold, then levels off at the diode drop.
- Ground symbols identify a circuit's common reference point and do not always imply a physical connection to Earth.
- Reversing the diode creates a negative limiter that conducts on negative inputs below approximately -0.7 V.
- Connecting oppositely oriented limiter diodes in parallel produces a double-sided limiter that clips both positive and negative excursions.
- Adding a DC bias source shifts a clamp threshold; for the positive branch described, the threshold is V0 + 0.7 V.
- Changing the diode direction, bias-source polarity, or whether the source connects to the anode or cathode creates four basic biased-limiter configurations.
- A rectifier converts AC to DC, while an inverter converts DC to AC; solar-panel systems use inverters to connect DC generation to AC buildings or the grid.
- The limiter and rectifier use the same VRD circuit; measuring across the diode gives the limiter output, while measuring across the resistor gives the rectifier output.
- A diode's one-way conduction selects one polarity of an AC waveform, forming the basis of a half-wave rectifier.
- In the positive CVD rectifier, the diode is off for Vin below 0.7 V, giving Vout = 0.
- When Vin exceeds 0.7 V, the diode conducts and the resistor output is Vout = Vin - 0.7 V.
- Reversing the diode produces a negative half-wave rectifier that passes the negative half-cycle after the input exceeds the forward-drop magnitude.
- The positive rectifier waveform contains only positive input excursions above 0.7 V; the negative half-cycle produces zero output.
- The output waveform trails the conducting input by the diode's 0.7 V drop, leaving a threshold gap before conduction begins.
- Expected practice circuits may include 1 to 3 resistors, 2 to 3 diodes, and 1 to 3 DC sources alongside an AC input.
- Lectures 4, 5, and 6 support the following week's lab, with analysis focused on diode states, circuit outputs, and transfer curves.
Transcript excerpt
0:01 Good afternoon. Lecture six. Um in this uh lecture today we are going to continue with our analysis of VRD circuits. Um we look at a couple of analyses using the CVD model and also how it relates to the ideal diode model and then sketch the voltage transfer characteristics for a diode limiter and a diode rectifier circuit. So let's look at the learning objectives for this lecture. The first one right here is analyzing circuits using CVD model. Then we look at the transfer
0:59 characteristic the voltage transfer characteristic of voltage limiter circuits and rectifier circuits and I'll point out that both of these circuits are exactly the same. The only difference is well we'll see what the difference is and then of course uh we'll just summarize with the expectations u um of this uh lecture slide. Okay. So the steps for analyzing using the CBD model. Uh first thing I'd like to point out the analysis applies equally to ideal diode also. Okay. Um if you haven't yet uh reviewed the previous lecture or you haven't uh solved the
1:46 three examples or the assigned practice problem sorry the three practice problems I would strongly uh urge you to do so before beginning this uh before beginning this lecture. Okay. So we have voltage sources. We have VRD circuit. We have voltage sources that have typically large values. Large values uh for these kind of circuits is at least 2 volts or more. And then on top of this voltage we apply AC waveforms. Now these AC waveforms will have both positive as well as negative values. Right? And so it can take any shape or form. This is sinosoidal, rectangular pulse.
2:34 Then there's triangular, square wave, uh sawtooth. All of these are examples of AC waveforms. Now AC waveform simply
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.