EE 2115 - Lec 03 - 2026_08_28
Overview
Hiren Trada reviews SI prefixes, then compares parallel and series load circuits using Ohm’s law, Kirchhoff’s laws, equivalent resistance, and power balance. With a 12 V source and two 1.44 Ω resistors, the parallel arrangement draws 16.67 A and 200 W, while the series arrangement draws 4.17 A and 50 W; wire resistance then illustrates why long-distance power transmission uses high voltage and low current.
Key takeaways
- Parallel loads share voltage: two 1.44 Ω resistors across 12 V each draw about 8.33 A, producing 16.67 A total and 200 W of demand.
- Series loads share current and add resistance: the same two 1.44 Ω resistors total 2.88 Ω, draw 4.17 A, and consume 50 W altogether.
- Equivalent resistance lets a source circuit be simplified: the two parallel 1.44 Ω loads appear to a 12 V source as a single 0.72 Ω load.
- KCL balances current at a node, while KVL balances voltage around a loop; the series example uses -12 V + VR1 + VR2 = 0.
- Wire resistance increases with length and decreases with conductor cross-sectional area; in the example, 0.05 Ω reduces load current from about 8.3 A to 7.79 A.
- High-voltage, low-current transmission reduces I²R losses over long distances, with voltage stepped down closer to consumers.
Chapters
- SI prefixes express the wide range of engineering values, from milli, micro, nano, and pico to kilo, mega, giga, and tera.
- Pico represents 10^-12 and femto represents 10^-15; examples include small currents and high operating frequencies.
- Prefixes also describe everyday measurements such as electronic-device storage, processor frequency, and response time.
- The lecture moves from a single source and load to circuits with two loads, covering parallel and series connections, KVL, KCL, and equivalent resistance.
- A battery is one example of a voltage source; a power outlet can also supply energy to a resistive load such as a heater.
- A filament bulb has resistance, but an LED’s small static and dynamic resistance does not adequately control current, so it needs a series resistor.
- Parallel components connect across the same two nodes, so each load receives the source voltage: 12 V in the worked example.
- Each 1.44 Ω resistor consumes 100 W at 12 V, so two parallel loads require 200 W from the source.
- Power signs track energy transfer mathematically: a 10 W phone adapter is -10 W and the phone receiving power is +10 W, summing to zero.
- Using P = VI, the source supplies 16.67 A to the two parallel resistors, each drawing about 8.33 A.
- KCL states that currents entering and leaving a node balance; here, the source current splits into the two branch currents and recombines.
- Two 1.44 Ω resistors in parallel have an equivalent resistance of 0.72 Ω, giving 12 V / 0.72 Ω = about 16.7 A.
- Series resistances add: two 1.44 Ω resistors produce 2.88 Ω total and draw 4.17 A from a 12 V source.
- Every component in a series path carries the same current, while the source voltage divides across the resistors.
- KVL gives -12 V + VR1 + VR2 = 0; each resistor consumes about 25 W, for 50 W total.
- Conductor resistance follows R = ρL/A: it increases with wire length and resistivity, and decreases as cross-sectional area increases.
- Even 0.05 Ω of wire resistance lowers the example load current from about 8.3 A to 7.79 A.
- The example estimates roughly 3 W lost in each direction of the wire path, or about 6.1 W total; long transmission lines make this loss a significant concern.
- Resistive line losses follow P = I²R, so reducing current is especially important when power must travel over long distances.
- Transmitting at higher voltage allows the same power to be sent with lower current, then voltage can be stepped down near consumers.
- Electricity losses depend on both transmission distance and where generation is located relative to residential and industrial users; California’s large geographic span is given as an example.
Transcript excerpt
0:00 Good afternoon. Let's continue from where we stopped last class. And that was this slide, the last slide of lecture two. So, let's see. In here is a small a small table of all the SI prefixes. These are the unit prefixes that we use in everyday engineering, everyday science. So, the reason we do these or use these is because in engineering especially, we deal with a large variation in the values of quantities. For instance, voltages and currents can range from singles and tens of volts to hundreds of
0:48 volts. Currents are typically much smaller. So, we use milliamps, microamps, and even nanoamps. Capacitances are typically in the microfarads. Inductances are usually in millifarads. Frequencies that we use in everyday usage in electrical engineering can run the gamut of a few few hundred hertz all the way to gigahertz, megahertz, and terahertz. So, we use common common the most common unit prefixes that we use are listed right here. To indicate the smaller scales, we use milli, micro, nano, and pico. Pico, by the way, is 10 raised to minus 12.
1:35 And then there's femto, which is 10 raised to minus 15, which I have on the next slide. And then, of course, to show what by effects we have kilo, mega, giga, tera at the other end. Um so, yeah, scan through the slide and you will see there examples of this all around all around us in everyday life. Um, whether we talk about storage memory in our electronic devices, the operating frequencies of our processors, um, response times, all of those uh can be described using unit prefixes. And there's one additional slide I added on at the end.
2:23 And here you can see this is pretty much a comprehensive table to illustrate uh illustrate both ends of the spectrum.
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.