EE 2115-01 - Lec 02 - 2026_08_26
Overview
Hiren Trada introduces circuit fundamentals by connecting charge, current, voltage, power, and energy to the behavior of resistors, diodes, inductors, capacitors, and switches. He derives Ohm’s law and the time-dependent inductor and capacitor relations, then distinguishes voltage sources from current sources using load examples and laboratory power-supply modes, CV and CC.
Key takeaways
- Ohm’s law, Kirchhoff’s Voltage Law, and Kirchhoff’s Current Law are the three foundational principles Trada identifies for solving circuit-analysis problems.
- A resistor’s ideal I-V relationship is linear, but a diode’s is nonlinear and rises sharply after its material-dependent forward threshold, roughly 0.6 to 0.7 V for silicon.
- Inductors obey v = L(di/dt) and store energy magnetically; capacitors obey i = C(dv/dt) and store energy electrically.
- An ideal short circuit has zero resistance and voltage drop, while an ideal open circuit carries zero current.
- A voltage source maintains voltage as load current changes, whereas a current source maintains current as load voltage changes.
- Laboratory supplies use CV and CC modes and pair them with current and voltage limits to reduce risk from circuit faults such as shorts.
Chapters
- Charge is denoted Q and measured in coulombs; current is the rate of charge flow, I = dQ/dt, measured in amperes.
- Voltage, current, power, and energy use the symbols V, I, P, and W; their unit symbols include V, A, W, and J.
- Electrical power is P = VI, and energy is found by integrating power over time, the area under a power-versus-time curve.
- The lecture notes a common notation convention: lowercase quantities often denote AC and uppercase quantities DC.
- An ideal resistor has a linear voltage-current relationship that passes through the origin: zero current corresponds to zero voltage.
- Ohm’s law, V = IR, gives voltage from current and resistance; rearranging gives I = V/R.
- Plotting V against I or I against V changes which quantity is on each axis, but both resistor characteristics remain straight lines.
- Trada identifies Ohm’s law, Kirchhoff’s Voltage Law, and Kirchhoff’s Current Law as the core principles underlying circuit analysis.
- Unlike R, L, and C, a diode is a nonlinear two-terminal semiconductor device.
- The diode symbol identifies the anode and cathode; conventional forward current is referenced from anode to cathode.
- Diode voltage is referenced positive at the anode and negative at the cathode, so a calculated negative value indicates polarity opposite to the chosen reference.
- The diode name and terminal terminology originate with the older vacuum-tube diode, which had two electrodes.
- A diode characteristic plots diode current ID against diode voltage VD and is nonlinear, with a steep current rise after forward conduction begins.
- Approximate forward thresholds depend on material: silicon is about 0.6 to 0.7 V, germanium about 0.2 to 0.3 V, and many LEDs about 1.2 to 1.5 V.
- The Shockley diode equation describes the exponential current-voltage relationship; William Shockley was one of the semiconductor transistor’s inventors.
- The lecture presents the diode as the course’s primary nonlinear two-terminal component.
- Inductors store energy in magnetic fields, while capacitors store energy in electric fields; both can return stored energy to a circuit.
- For an inductor, voltage is proportional to the rate of current change: vL = L(di/dt).
- For a capacitor, current is proportional to the rate of voltage change: iC = C(dv/dt).
- Because these quantities change during energy transfer, inductor and capacitor voltages and currents depend on time.
- A subscript identifies a particular component: VL, for example, means the voltage across an inductor.
- Writing VL(t) indicates that inductor voltage varies as a function of time and can be evaluated at specific time values.
- Integrating the inductor and capacitor differential relations gives corresponding current-from-voltage and voltage-from-current forms.
- Trada describes inductors and capacitors as duals, with the inductor relation centered on changing current and the capacitor relation on changing voltage.
- An open switch breaks the circuit path and prevents current flow; a closed switch completes the path and permits current flow.
- An ideal short circuit has zero resistance and zero voltage drop, while an ideal open circuit has infinite resistance and zero current.
- A real switch should block current when open and have minimal voltage drop when closed to minimize power loss.
- Trada uses a household 120 V outlet as an example of voltage present without current flowing until a device completes the circuit.
- The resistor is shown as a zigzag, the capacitor as two equal parallel plates, and the inductor as a coil.
- The diode and switch symbols represent directional conduction and circuit interruption or connection, respectively.
- Resistors, inductors, and capacitors form the fundamental RLC components; inductors and capacitors can store and later release energy.
- A voltage source holds voltage constant while current changes with the load: at 10 V, resistors of 1, 10, and 100 ohms draw 10, 1, and 0.1 A.
- A current source holds current constant while voltage changes with the load: a 10 A source across 1, 10, and 100 ohms requires 10, 100, and 1,000 V.
- Bench power supplies commonly offer CV, constant-voltage mode, and CC, constant-current mode; batteries, adapters, and outlets generally act as voltage sources.
- Current limits in CV mode and voltage limits in CC mode protect circuits if a short or other fault causes the load to change unexpectedly.
Transcript excerpt
0:02 and then lecture two. Let me first begin by asking does anyone have any questions uh regarding the syllabus? Anything on the canvas website that I can answer? Okay. [clears throat] All right. lecture two. So today we'll look at fundamentals of voltage and current sources. So sources and then a few example problems about power and energy calculations. If you have taken the physics you are currently taking it some of it would be familiar to you. Uh
0:49 regardless of that we will cover this in here. All right. So last class we looked at definitions, notations, uh units, just a overview slide of what we looked at. Passive components, resistors, capacitors, inductors, uh units, um amps, volts, and uh sorry not amps, volts, uh capacitors, farads, resistors, ohms, inductors, Henry. And then we looked at the com uh quantities, voltage, current, power, and energy. voltage volts. Um, current ampers, power is watts, and uh, energy in jewels. So, I know we were late in starting. So, I believe
1:39 we covered this one. Can someone please remind me? Did we cover this? Okay. All right. Well, then let's just talk about it a little bit then. All right. So, we talked [clears throat] about what charge is, fundamental charge. uh unit of charge is culum named after Charles Culum. Units if you notice here the unit for charge is kum voltage is volts current is ampers power is watt. Energy is jewel. All of these units are always labeled in uppercase letter. Okay. So this would be uppercase C, V, A, W and J. Okay. So units are always always always expressed in uppercase
2:29 letters. [clears throat] And then quantities depending on whether we are dealing with AC or DC would be uppercase or lower case. If it's AC then typically we use
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.