EE 2115-01 - Lec 32 - 2026_11_18
Overview
Hiren Trada introduces Laplace transforms as a way to turn circuit differential equations into algebraic equations, then applies the method to RC circuits and their transfer functions. The lecture also connects RC behavior to semiconductor parasitic capacitance and op-amp signal conditioning, and compares band-stop and band-pass outputs from a parallel-LC network with a series resistor resonating at 18.4 kHz.
Key takeaways
- Parasitic capacitance at semiconductor inputs and between adjacent conductors can round fast signal edges; in the example with 10 kΩ, 100 kΩ, and 1 nF input capacitance, about 100 pF of compensation capacitance sharpens the response.
- A parallel LC network with a series resistor produces a band-stop output across the resistor and a band-pass output across the LC branch; the example's 18.4 kHz resonance is suppressed at the resistor output.
- For zero initial conditions, Laplace transforms map derivatives to multiplication by s, turning circuit differential equations into algebraic equations that can be solved using impedance methods.
- A series RC circuit with capacitor output has H(s) = 1/(1 + sRC) and step response V0(1 - e^(-t/RC)); resistor output has H(s) = sRC/(1 + sRC) and decays after the step.
- High-impedance sensors can combine large Thévenin resistance with packaging capacitance, while op-amp conditioning may introduce edge oscillations that require attention to circuit design.
Chapters
- Unintentional capacitance between conductors in semiconductor wiring, and stored charge in device junctions and MOSFET gates, can slow transitions.
- A capacitor placed in parallel with R2 in a voltage divider can compensate for device input capacitance and sharpen the output edge.
- An LTspice example uses R1 = 10 kΩ, R2 = 100 kΩ, and 1 nF input capacitance, with about 100 pF added for compensation.
- Low-voltage sensors such as strain gauges, flow meters, level sensors, temperature sensors, and humidity sensors can have large Thévenin resistance and packaging capacitance.
- The sensor is modeled as a source and RTH feeding a non-inverting op-amp amplifier, with a capacitor used to bypass AC signals.
- Op-amp outputs can oscillate around the desired level at both rising and falling step edges, a behavior students may observe in Lab 12.
- With L and C in parallel and a resistor in series, measuring output across the resistor produces a band-stop, or band-reject, response.
- The example LC network resonates at 18.4 kHz; the resistor output approaches zero near resonance while nearby frequencies such as 16 kHz and 21 kHz mostly pass.
- Measuring across the parallel LC instead produces a band-pass response, useful for selecting a radio signal or suppressing unwanted noise.
- One energy-storage component typically yields a first-order differential equation, while two yield a second-order equation; additional capacitors and inductors increase the difficulty.
- Like phasor analysis for sinusoidal steady state, Laplace transforms convert differential equations into algebraic expressions.
- After solving in the transformed domain with tools such as KVL, KCL, and Ohm's law, an inverse Laplace transform returns the result to the time domain.
- A time function x(t), such as voltage or current, maps to X(s) through the Laplace transform integral from zero to infinity of x(t)e^(-st).
- The transform is introduced under the assumption of zero initial conditions, meaning no initial stored charge or energy.
- A unit step u(t) transforms to 1/s, while e^(-t/τ)u(t) transforms to τ/(1 + τs), a form relevant to first-order RC and RL responses.
- With zero initial conditions, differentiation maps to multiplication by s, integration maps to division by s, and a delay td introduces the factor e^(-s td).
- Applying the transform to a linear differential equation replaces first and higher derivatives with s, s², and higher powers, yielding an algebraic equation.
- The transfer function H(s) is defined as output divided by input in the transformed domain; for sinusoidal steady-state analysis, s can be evaluated as jω.
- For a series RC circuit with output across the capacitor, KVL gives Vin = VR + VC and the capacitor current is C dVC/dt.
- Combining Ohm's law with the capacitor relation produces a first-order equation with time constant τ = RC.
- Transforming and rearranging gives H(s) = Vout(s)/Vin(s) = 1/(1 + sRC), the low-pass response.
- In the s-domain, the resistor impedance remains R and the capacitor impedance becomes 1/(sC), allowing Ohm's law and voltage division to replace differential-equation calculations.
- For output across the capacitor, voltage division gives ZC/(R + ZC), equivalent to 1/(1 + sRC).
- The transformed impedance method produces the same transfer function as the direct differential-equation derivation.
- A unit-step input has transform 1/s, so the capacitor-output response contains the factor 1/[s(1 + sRC)].
- Partial fractions separate the expression into step and decaying-exponential terms, which can be inverse-transformed directly.
- For a step of amplitude V0 from an initially uncharged capacitor, Vout(t) = V0(1 - e^(-t/RC)); the result matches the earlier time-domain solution.
- Taking output across the resistor gives H(s) = R/(R + 1/(sC)) = sRC/(1 + sRC), the complementary high-pass response.
- At the instant a step is applied, the capacitor voltage cannot change instantly, so the source voltage initially appears across the resistor and then decays as the capacitor charges.
- Laplace-domain impedances enable standard voltage division and Ohm's law; an inverse transform then converts the result back to a time-domain waveform.
Transcript excerpt
0:01 Okay, good afternoon. Uh, today we'll begin uh new techniques for circuit analysis. Uh, new mathematical techniques. So, I was talking about laplas transforms previously. Today we'll see a little bit of introduction to laplas transforms and see how it applies to our circuits. Uh, before that uh we're going to look at uh maybe for the first 5 to 10 minutes of a few applications for RC circuits. Okay. All right. So we know that when we have a capacitor, capacitor is going to charge and discharge. So when we feed it a square wave input or a
0:50 step input, there is a transition that takes place. the transition follows the charging and the discharging curve which is exponential. And so [clears throat] often times what happens is uh instead of a sharp response like this the output we have a curve response and [clears throat] uh this is primarily seen in semiconductor devices. So if you recall a few lectures ago or a few weeks ago I had used an example of microchips and in those microchips we have wires running from point A to point B, point C to point D um all on top of each other. So multiple wires crisscrossing and they're separated by an insulating material which causes
1:38 so let's do this. So let's say this is point A to point B and then I have point C to point D and of course it is separated by a insulating material between the two. So it is two conductors separated by an insulator. So this cross-section right here forms a capacitance. It's known as a parasitic capacitance. It is unwanted. Okay. [snorts] U also in semiconductor devices in general whether it's a diode
2:26 or a transistor uh feets MOSFETs uh there are charges that are stored um
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.