EE 2115-01 - Lec 07 - 2026_09_09
Overview
Hiren Trada begins with LED drive design, showing how a 1.9 V LED supplied by two 1.5 V cells needs a series resistor of about 55 Ω, typically rounded to 56 Ω, to limit current to 20 mA. He then develops Thévenin and Norton equivalents, explaining how complex linear circuits can be reduced to terminal models and how voltage and current sources combine using KVL and KCL.
Key takeaways
- For the example 1.9 V LED powered by 3 V, a 55 Ω resistor limits current to 20 mA; selecting a standard 56 Ω part provides a practical nearby value.
- That 56 Ω resistor dissipates about 22 mW at 20 mA, below the 1/8 W rating cited for standard resistors.
- A linear circuit's Thévenin equivalent is VTH in series with RTH, while its Norton equivalent is IN in parallel with the same resistance.
- The Thévenin-Norton conversion relationship is VTH = IN × RTH, enabling source transformation without changing terminal behavior.
- Series voltage sources combine algebraically according to KVL and polarity; parallel current sources combine algebraically according to KCL and direction.
- A load connected to a Thévenin equivalent receives current I = VTH / (RTH + Req), reducing a complex source-and-load problem to a series-circuit calculation.
Chapters
- The example LED has a 1.9 V forward voltage and a 20 mA operating-current requirement; LED forward voltage varies with semiconductor material and color.
- Two 1.5 V cells in series provide 3 V, leaving 1.1 V to drop across a protective resistor.
- Ohm's law gives R = (3 V - 1.9 V) / 20 mA = 55 Ω; a standard value near 56 Ω allows for resistor tolerance.
- Without adequate current limiting, excessive current can damage the LED; a small button cell may limit current enough for some low-cost LED trinkets to work without a separate resistor.
- The Shockley diode equation is reviewed, along with its association with transistor pioneers William Shockley, John Bardeen, and Walter Brattain, who received the 1956 Nobel Prize in Physics.
- For course calculations, use a thermal voltage of 26 mV at approximately 300 K when no value is provided.
- The diode model includes saturation current, ideality factor n, typically between 1 and 2, and series resistance.
- LTspice includes readily available models for components sold by its associated manufacturer, so other manufacturers' parts may require different model parameters.
- Terminal behavior means the voltage and current measured at a pair of external terminals, without needing to know every component inside a network.
- Léon Charles Thévenin's theorem represents a linear circuit with sources and resistors as one voltage source, VTH, in series with one resistance, RTH.
- This equivalent model applies to circuits containing voltage and current sources, provided the relevant circuit is linear.
- The reduction is useful when a complex source, such as a power supply, is characterized only by its output at the terminals.
- A resistive load network can be reduced to one equivalent resistance, Req, connected to the source circuit's output terminals.
- After connecting the load to the Thévenin model, the series current is I = VTH / (RTH + Req).
- Once current is known, Ohm's law gives voltage drops across the Thévenin resistance and the load.
- An amplifier driving an 8 Ω speaker illustrates how a complicated downstream circuit can be described by its effective load resistance.
- Edward Norton developed the corresponding model of a single current source, IN, in parallel with a resistance, RN.
- The Norton resistance is the same equivalent resistance as the Thévenin resistance: RN = RTH.
- A Thévenin voltage source in series with RTH and a Norton current source in parallel with that resistance are equivalent at the same terminals.
- Source transformation follows VTH = IN × RTH, allowing conversion between the two circuit forms.
- Voltage sources combine in series: two aligned 1.5 V cells provide 3 V, and eight 1.5 V cells provide 12 V.
- Use KVL to add or subtract series source voltages according to their polarities; mismatched battery voltages should not be connected directly in parallel.
- Current sources combine in parallel, not in series, and KCL determines the resulting current.
- Parallel current sources pointing in the same direction add, while sources pointing in opposite directions subtract.
- A 5 V source and a 7 V source connected with aligned polarities produce 12 V between the outer terminals.
- With the sources opposing one another, the net voltage is 7 V - 5 V = 2 V, with polarity set by the stronger source.
- A source marked -7 V has polarity opposite to the chosen reference; combined with -5 V in the illustrated orientation, the result is -12 V.
- Voltage signs depend on the selected measurement reference, just as reversing multimeter leads changes a reading's sign.
- Two parallel current sources of 10 A and 12 A pointing in the same direction combine to give 22 A.
- When the 10 A and 12 A sources point in opposite directions, the net current is 2 A toward the stronger 12 A source.
- The examples use KCL to replace multiple parallel sources with one equivalent current source.
- The lecture ends shortly after beginning a further current-source orientation example.
Transcript excerpt
0:02 All right, good afternoon. Sorry, it's taken every time there's a long break or something. I don't know. Something goes wrong with the technology. No idea what's going on. Anyway, let's move this out of the way and your notes. Okay. So, lecture seven. And again, I apologize if we go over one or two slides over time. You can leave uh when the class is over or you can hang out till 4:30 in the school room if you want
0:51 to. All right. So at the end of lecture 06 in the slides there was a question about driving an LED. So let's just cover that. So we have a LED here. [clears throat] Now LEDs again are diodes. So it requires a certain amount of voltage for them to turn on. And depending on the dopen material we use the color of the LED changes. Right? And more [clears throat] importantly the voltage that is required to turn on the LED will also change depending on that material. So red LEDs, green LEDs they are somewhere around 1.1 1.5ish. So in this one in this example we have diode voltage as 1.9 volts. So almost 2 volts. Um there are other LEDs which can
1:42 uh operate below below 1.1 or 1.2 volts. But in our example, we are using 1.9 volt LED and it requires at least 20 milliamps of current. Okay, it's not just the voltage which is the pressure differential but also requires certain amount of current for it to turn on. So 1.9 volts standard battery is only 1.5 volt, right? AAA batteries are 1.5 volt batteries. So we wish to have a uh let's say a flashlight and we want to turn on the LED or drive the LED using batteries, we need at
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.