EE 2115 - Lec 04 - 2026_09_01
Overview
Hiren Trada develops equivalent resistance as a way to describe a resistor network from its terminals, deriving the series and parallel rules and demonstrating reduction of a 10 V network to about 4.16 kΩ. The lecture then models practical sources with internal resistance, derives the maximum power transfer condition RL = RS and Pmax = VS²/(4RS), and estimates battery resistance from voltage change under a stepped test current.
Key takeaways
- Equivalent resistance describes a network only relative to a chosen pair of terminals, because the current paths and therefore the apparent resistance can change with the observation points.
- Series resistors have Req = ΣRi, while parallel resistors have 1/Req = Σ(1/Ri); a parallel result must be smaller than the smallest branch resistance.
- For the worked 10 V resistor network, reducing the groups yields about 4.16 kΩ and predicts a source current of about 2.4 mA without calculating every internal branch current.
- A practical voltage source can be represented by VS in series with RS, giving load current VS/(RS + RL) and load voltage VS RL/(RS + RL).
- Maximum load power occurs when RL = RS, with Pmax = VS²/(4RS); this condition does not imply maximum efficiency.
- Battery internal resistance can be estimated from a stepped current test using |ΔV/ΔI|; the cited fresh alkaline AA range is 150 to 300 milliohms.
Chapters
- The lecture sets four goals: find total equivalent resistance, model a real power source, derive maximum power transfer, and assess battery internal resistance.
- A resistor network can be treated as a sealed box and replaced by one equivalent resistance as viewed from a specified pair of terminals.
- Equivalent resistance depends on the chosen terminals because current can encounter different paths through the network.
- In a series path with no branching, the same current flows through every resistor.
- Using V = IR, the total voltage across R1 and R2 is I(R1 + R2), so Req = R1 + R2.
- For n series resistors, the equivalent resistance is the sum of all n resistance values.
- Parallel components connect across the same two nodes, so each resistor has the same voltage while the total current divides among branches.
- From Ohm's law, 1/Req = 1/R1 + 1/R2; for n branches, add all reciprocals and take the reciprocal of the result.
- A parallel equivalent resistance is always less than the smallest branch resistance, providing a quick check for calculations.
- The worked example connects a 10 V source to a mixed resistor network and simplifies recognizable series and parallel groups.
- The reduction gives Req of about 4.16 kΩ, leading to a source current of about 2.4 mA by Ohm's law.
- Independent series or parallel groups can be reduced in either order, but a resistor that is neither in series nor parallel with another must wait until surrounding groups are simplified.
- Delta and wye configurations address networks that cannot be simplified directly using only series and parallel rules.
- A delta has three outer nodes; converting it to a wye introduces a central fourth node and changes three resistors into three branches.
- The lecture illustrates transforming two delta groups into wye forms so shared branches can then be combined through series and parallel reductions.
- Ideal components use relationships such as V = IR for a resistor, while inductors and capacitors involve time-varying quantities through L di/dt and C dv/dt.
- An ideal voltage source connected to zero resistance, or an ideal current source driving infinite resistance, implies unbounded power under the idealized model.
- A practical source must account for limited power rather than allowing the unrestricted voltage or current predicted by ideal-source assumptions.
- A practical voltage source is modeled as an ideal source VS in series with internal resistance RS, also called source resistance.
- With no load, the output is open circuit and can reach the source's stated voltage; once load current flows, some voltage drops across RS.
- For load resistance RL, the current is VS/(RS + RL), the load voltage is VS RL/(RS + RL), and the internal drop is IL RS.
- The example describes a source rated for 12 V with a 100 W power limit and notes that practical supply output voltage falls as internal voltage drop increases.
- The maximum power transfer theorem states that load power is greatest when RL equals the source resistance RS.
- At the matched condition, maximum load power is Pmax = VS²/(4RS).
- Maximum power transfer does not mean maximum efficiency; matching the load and source resistances is a power-delivery condition.
- A battery can be modeled as an open-circuit voltage VS in series with internal resistance RS, which causes terminal voltage to fall under load.
- A small stepped test current, from I1 to I2, produces a voltage change; the resistance magnitude is estimated as |ΔV/ΔI|.
- Fresh alkaline batteries are cited as typically having about 150 to 300 milliohms of internal resistance, with unit-to-unit variation.
- The example voltage change from about 1.48 V to 1.37 V for a 0.5 A current step corresponds to roughly 0.22 Ω; the practice result is approximately 214 milliohms.
Transcript excerpt
0:02 Good afternoon. Um in lecture four we are going to look at uh four different things with four objectives. Uh first we are going to look at our EQ that is the total equivalent resistance of a network of resistors. Let's switch over to the notes. All right. There we go. So objective one total equivalent resistance um for a network of resistors. Uh second is to model a real life power source. Third is to derive the load conditions when we are trying to transfer maximum power from a source to a load. And
0:51 finally, we look at a real life battery and see what the effects are um of a real life battery um on an external supplied voltage source. So let's first talk about what we covered last lecture. So in lecture three, we looked at a source and a load circuit. That's the simplest of circuits where we have one source applying energy to a load and then we define the power the power equation product of V and I. So P= VI and then power conservation every energy uh every unit of energy that is delivered must be consumed it's neither created nor destroyed.
1:39 And then we looked at how we can connect multiple loads either in parallel or in series. Okay. So now since we can connect uh resistors in multiple different ways, sometimes they could be in parallel, sometimes they could be in series, sometimes they are neither in parallel nor in series. Now if we are trying to find uh the behavior of a circuit between two terminals between a pair of terminals we do not necessarily need to know what is going on inside that circuit. Specifically for a source, a source is going to supply energy to a network of resistors. And the resistors
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.