EE 2115-03 - Lec 30 - 2026_11_13
Overview
Hiren Trada introduces frequency-selective filters through wireless examples, then defines the transfer function as the ratio of output to input voltage and explains how passive RC and RL circuits shape signal amplitude and phase without changing frequency. He derives low-pass and high-pass behavior from capacitor and inductor impedance, compares first-order filters with second-order band-pass and band-stop designs, and identifies cutoff frequency as the transition point where output magnitude is about 0.707 of the input.
Key takeaways
- A transfer function H(f) = Vout/Vin describes how a circuit changes a signal at each frequency, making it possible to predict output from a known input.
- An RC circuit is low-pass when output is taken across the capacitor and high-pass when output is taken across the resistor.
- For an RC filter, fc = 1/(2πRC); at cutoff, output magnitude is approximately 70.7% of input, and the transition is gradual rather than an abrupt pass-or-block boundary.
- An RL circuit is low-pass across the resistor and high-pass across the inductor, with cutoff frequency fc = R/(2πL).
- For sinusoidal inputs, filters change amplitude and phase but preserve frequency; the complex transfer function encodes both effects.
- A circuit with one energy-storage element is first order, while combining two filter sections can create second-order band-pass or band-stop behavior.
Chapters
- Electronic filters pass or attenuate signals according to frequency, much like a frequency-selective sieve.
- A phone's front end selects its carrier's frequency while rejecting other signals, reducing interference from sources such as AM, FM, television, and other mobile networks.
- The lecture cites 2.4 GHz and 5 GHz as consumer-use bands and notes that mobile carriers acquire spectrum rights through government auctions.
- Treating a circuit as a two-port black box, the transfer function H(f) is defined as Vout/Vin and predicts output from input.
- A signal can contain many sine-wave components; a filter can amplify some frequency components and attenuate others while their frequencies remain unchanged.
- Filters made only from resistors, capacitors, and inductors are passive; adding op amps creates active filters, which are introduced as a later topic.
- One energy-storage element gives a first-order RC or RL filter; combining filter stages can produce second-order band-pass or band-stop behavior.
- An RC circuit with output across the capacitor is a low-pass filter; taking output across the resistor makes the same circuit a high-pass filter.
- At low frequency, a capacitor approaches an open circuit; at high frequency, it approaches a short circuit, explaining the RC low-pass response.
- For an RC low-pass filter, H(f) = 1/(1 + j f/fc), with cutoff frequency fc = 1/(2πRC); at fc, output magnitude is approximately 0.707 of input.
- Below cutoff, signals are treated as passed and above cutoff as attenuated, though the response changes gradually rather than switching abruptly.
- For an RL circuit, output across the resistor produces low-pass behavior, while output across the inductor produces high-pass behavior.
- The RL cutoff depends on its components, with fc = R/(2πL); its normalized response has the same general form as the corresponding RC filter.
- Inductor impedance rises with frequency, while capacitor impedance falls with frequency, enabling the complementary RC and RL filter responses.
- An AC filter changes signal magnitude and phase, but it does not change the input frequency.
- Because H is complex, its frequency response includes both a magnitude and a phase angle, with equations provided for each.
- The lecture closes by directing students to review the current material alongside lecture sections 23B and 23C.
Transcript excerpt
0:01 Okay. So last lecture class before the exam uh before actually the two review sessions we did we had talked about AC analysis and AC fundamentals right and I the point of doing those was it's going to be useful um to understand what's coming next week. So we need a little bit more um a little bit of time today. We're going to cover what is known as filters or filter applications. So let's look at what filters are. Uh all right filters as the name suggests are filtering out something. It's like a seieve except in this case it's an electronic seieve right. So what is it what is it trying to filter out? trying
0:49 to filter out signals but the quantity that is being filtered out is based on the frequency of that signal and that's what electronic filters do. Electronic filters act like an electronic se based on the frequency depending on the frequency of a particular signal it'll be allowed to pass through or it would be blocked. Okay. Now, there are signals all around us, wired as well as wireless. I'm often fond of using wireless as an example because it's more tangible, ironically, pun intended. Um, so wireless signals are all around us. We can't see them obviously. Uh, but you have AM radio stations, FM radio stations, television signals, satellite,
1:36 mobile phones. So, let's use mobile phones as an example, right? You have AT&T, Verizon, and T-Mobile. All three of them operate at a certain frequency. Now frequencies are a valuable u valuable asset. Okay. So the government of every control I don't know what's happening to me the last year the government of every country controls who can use a particular frequency. So for instance 2.4 GHz and 5 GHz were opened up for
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.