9:3 Dimensional Analysis - Re, Eu, Fr and Methodology
Overview
Derek Elsworth shows how Buckingham Pi analysis reduces pipe-flow behavior to dimensionless groups, deriving a Reynolds-number relationship for pressure loss and explaining how relative roughness adds another controlling parameter. He connects the method to Reynolds and Euler similarity in scaled experiments, from pipe models to aircraft and bridge aeroelasticity, and derives the Darcy-Weisbach head-loss equation.
Key takeaways
- For pipe pressure loss modeled with Δp/L, D, V, ρ, and μ, Buckingham Pi gives two groups: (Δp/L)D/(ρV²) and μ/(ρVD), the latter being 1/Re.
- Including pipe roughness ε creates a third group, ε/D; roughness is irrelevant to laminar friction behavior but can influence turbulent friction.
- The Darcy-Weisbach equation expresses head loss as hL = f(L/D)(V²/2g), and the Darcy friction factor for laminar circular-pipe flow is 64/Re.
- Reliable scale-model transfer requires geometric similarity and matched Reynolds number; matching Euler number then links model and prototype pressure or force behavior.
- Buckingham Pi analysis can identify how to organize experiments without first solving the governing equations, reducing results to a small set of dimensionless relationships.
Chapters
- A bridge deck can shed alternating vortices in a von Kármán vortex street as wind passes over it.
- When vortex-shedding frequency matches a bridge's natural frequency, resonance can amplify motion and damage the structure.
- Bridge and aircraft models require more than fluid-flow similarity when structural elasticity also affects their behavior.
- Geometric similitude requires matching model and prototype shapes and length proportions.
- Kinematic similitude is achieved by matching Reynolds numbers, not necessarily flow velocities.
- Matching Reynolds number allows model pressure or force measurements to be transferred through an Euler-number relationship, subject to additional constraints such as structural stiffness.
- Elsworth defines a pipe-flow system using diameter D, average velocity V, density ρ, dynamic viscosity μ, and pressure gradient Δp/L.
- The goal is to relate pressure loss to measurable fluid and pipe properties while reducing the number of experiments.
- Expressing pressure change per unit length avoids treating pipe length as a separate variable in the initial parameter set.
- For a horizontal pipe with equal upstream and downstream areas, elevation and velocity-head terms cancel in the energy equation.
- With no pump head added, the pressure-head difference, (p₁ − p₂)/(ρg), equals the head loss hL.
- A basic experiment measures pressure drop and flow rate, then converts flow rate to average velocity.
- The initial pipe-flow model has five variables: pressure gradient, D, V, ρ, and μ.
- The variables span three fundamental dimensions, mass, length, and time, so Buckingham Pi predicts 5 − 3 = 2 dimensionless groups.
- Elsworth chooses D, V, and ρ as repeating variables because together they contain all three fundamental dimensions.
- The first group combines Δp/L with D, V, and ρ, assigning exponents so mass, length, and time powers each sum to zero.
- Solving the dimensional equations gives Pi₁ = (Δp/L)D/(ρV²).
- Rearrangement identifies an Euler-like pressure ratio multiplied by the geometric ratio D/L.
- Dynamic viscosity has dimensions of mass per length per time, which can be derived from stress divided by velocity gradient.
- Combining μ with the repeating variables yields Pi₂ = μ/(ρVD), the reciprocal of Reynolds number.
- The pipe-flow relationship can therefore be expressed as a connection between pressure-loss behavior and Re.
- Each experiment supplies a pressure drop and an average velocity, which together determine values for the pressure group and Reynolds number.
- Increasing pressure raises velocity, while the V² term changes the pressure-group value nonlinearly.
- Plotting the dimensionless measurements reveals a relationship that can organize results across different operating conditions.
- Adding pipe roughness ε raises the variable count to six and the predicted number of groups to 6 − 3 = 3.
- Because ε and D are both lengths, their dimensionless ratio ε/D represents relative roughness.
- In laminar flow, friction behavior is independent of ε/D; in turbulent flow, roughness can affect friction and different roughness ratios produce different curves.
- Rearranging the pressure ratio produces the pipe head-loss form hL = f(L/D)(V²/2g), where f is the friction factor.
- For fully developed laminar flow in a circular pipe, the Darcy friction factor is 64/Re.
- For turbulent flow, the friction factor depends on Reynolds number and, where relevant, relative roughness.
- Laminar Navier-Stokes solutions assume a Newtonian fluid and produce a parabolic pipe velocity profile, with zero velocity at the wall and a maximum at the center.
- Turbulent pipe flow has fluctuating particle paths and a fuller, more nearly uniform average velocity profile, so the laminar solution does not describe its behavior.
- For a model and prototype with matching geometry and Reynolds number, a shared Euler-number relationship allows measured model pressures or forces to be scaled to the prototype.
- Elsworth points to a wind-tunnel example involving a fifth-scale dish model, where Reynolds matching sets test conditions and Euler scaling converts measured forces.
- The alternative force-length-time dimensional system can simplify unit calculations, including for viscosity expressed in pascal-seconds.
- Non-dimensional methods also appear in groundwater pumping tests and petroleum-reservoir analysis, making Buckingham Pi useful across engineering and science.
Transcript excerpt
0:02 so some movies to get us going on we talking about dimensional analysis and how we can use some recipe that we'll talk about today called Buckingham pie to be able to figure out what the dimensional non-dimensional parameters are that allow us to describe these systems we'll do it for pipe flow today but there are obviously systems which are more complex than that and this is one of those because it's kind of what would be called I guess Aero elasticity and that is uh just like the Tacoma Narrows Bridge we talked about there being flow we talked about there being two major parameters we could worry about uh that we had for any model we had to have
0:51 um geometric similarity scaled down model obviously this is a scaled down model what is it probably 100 scale I'm not really sure we had to have what we called kinematic similarity in that the air flowing across it was it the same Reynolds number not the same velocity but the same Reynolds number as the real system and then if that was the case we could work out what the forces are applied to it from the Euler number so those are the three 10 variables so this is more complex than that in that you'd also have to get similarity in the elasticity of the uh the bridge and so that's an extra feature that we'd have to to worry about and so this is a wind tunnel looking at the behavioral Bridge uh uh you know we showed the Tacoma Narrows
1:38 Bridge and talked about the idea that if the wind is blowing at such a velocity that it sheds vortices off the deck top and bottom on this so-called Von Carmen Vortex Street then if that resonant frequency of that
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Derek Elsworth.