MAT291: Lecture 20 - Circulation and Flux Integrals
Overview
MAT291 Lecture 20 develops circulation and flux integrals for vector fields along curves, linking circulation to work and flux to the field component crossing a boundary. It gives parametrization-based formulas, explains orientation and outward normals, and works through a curve integral and two flux examples, including a circle of radius 2 and a boundary formed by a parabola and a line.
Key takeaways
- Circulation is computed as ∫F(r(t)) · r′(t) dt, so reversing a curve’s orientation negates the result.
- Flux is computed from the normal component of a vector field; in the plane, an outward normal element can be written as N̂ ds = (y′(t), −x′(t)) dt for a positively oriented closed curve.
- The sign of flux has a physical interpretation: positive flux is outward flow associated with a source, and negative flux is inward flow associated with a sink.
- For a circle of radius 2, polar coordinates give the outward normal directly as (cos θ, sin θ) and the arc length as 2 dθ.
- A piecewise boundary must be split into its geometric sections, with each section parametrized in the direction that preserves the closed traversal and outward normal.
Chapters
- Circulation is introduced as the work done by a vector field, such as a force, along a trajectory.
- The tangential unit vector T̂ selects the component of the field that contributes to work.
- A field perpendicular to the path contributes zero circulation; an angle below 90° contributes positively, while an angle above 90° contributes negatively.
- For a parametrized curve r(t), the tangent direction follows r′(t).
- Reversing a curve’s orientation reverses the sign of its circulation integral.
- The orientation from a starting point to an endpoint is specified by the direction in which t increases.
- For F(x,y) = (y², x) and r(t) = (t, t³), with 0 ≤ t ≤ 1, substitution gives F(r(t)) = (t⁶, t).
- The derivative is r′(t) = (1, 3t²), so the dot product integrand is t⁶ + 3t³.
- Integrating from 0 to 1 gives circulation 25/28; reversing the path from (1,1) to (0,0) gives −25/28.
- A scalar line integral uses the curve’s arc length, while circulation uses the vector differential dr and a dot product.
- Scalar examples include accumulating quantities such as mass or charge; vector-field examples include forces and electric or magnetic fields.
- For circulation, orientation affects the result because the tangent direction is part of the integrand.
- Flux uses the normal unit vector N̂ rather than the tangent T̂ to measure the field component crossing a curve.
- A vector field can be decomposed into tangential circulation and normal flux components.
- Examples of quantities crossing a boundary include fluid, heat, mass, and electric charge.
- Positive flux corresponds to a field leaving the boundary, while negative flux corresponds to a field entering it.
- The lecture relates outward flux to a source and inward flux to a sink, including positive and negative electric charges as examples.
- In two dimensions, a normal can be formed by swapping the tangent components and negating one; the outward choice must be checked against the curve’s geometry.
- For r(t) = (x(t), y(t)), the tangent is based on r′(t) = (x′(t), y′(t)).
- The lecture uses the outward normal direction proportional to (y′(t), −x′(t)).
- Normalizing N̂ and multiplying by ds cancels the speed magnitude, leaving N̂ ds = (y′(t), −x′(t)) dt.
- The circle x² + y² = 4 is parametrized by r(t) = (2 cos t, 2 sin t), for 0 ≤ t ≤ 2π.
- The outward normal is checked at t = 0 and t = π/2, where it points in the positive x and positive y directions, respectively.
- Using the lecture’s stated field and calculation, the parametric method produces a reported flux of 12π.
- For the radius-2 circle, the outward normal is the polar unit vector r̂ = (cos θ, sin θ).
- The arc-length element is ds = r dθ = 2 dθ, avoiding a separate calculation of the normalized tangent.
- The lecture presents this coordinate-based method as a shorter alternative to parametrization for geometries that match a standard coordinate system.
- The closed boundary consists of y = x² for −2 ≤ x ≤ 2 and the top segment y = 4, traversed from x = 2 back to x = −2.
- For the parabola, r(t) = (t, t²) and the outward normal direction is proportional to (2t, −1); the lecture reports a contribution of −32/15.
- For the top segment, r(t) = (−t, 4) with −2 ≤ t ≤ 2, giving the upward normal (0,1) and a reported contribution of 64.
- Adding the two reported contributions gives total flux 928/15; the parameter −t ensures the top segment is traversed in the direction needed to close the curve.
Transcript excerpt
0:01 Good morning, everyone. So, yesterday we talked about in a scalar and integrals over curves, and today we all we will talk about uh vector uh functions or vector fields integrals over curves. Okay? And then that divides into two different categories. One is the circulation of a vector field, and the other one is a flux of a vector field. So, how much of a function, a vector function, is circulating around a curve, right? Or over a curve, and how much of it crosses it? We're going to look at this. This is a
0:48 very, very important topic when we talk about vector calculus later in the semester, when we go through curl and divergence. You will see these again, okay? But in 2D perhaps. >> [snorts] >> Uh well, for the divergence in 2D. For the circulation, it's always a curve. Anyway, so let's go through the definitions. Okay, what is a circulation? What is a flux? And then how do we calculate each of these? So, the circulation of a vector field over a curve comes from the definition of the work done by a force, basically. So, imagine Imagine that vector field, vector
1:38 function, as a force. As you know, force has an amplitude and has a direction. So, that's why you can consider it as a vector field, right? Okay. [clears throat] So, circulation is very, very similar to the work done by that force, by that vector field. And the way you remember it from physics is that in order to calculate the work done by a vector a force over a curve over a trajectory, you would calculate f. t ds. Do you remember this? Which is basically the projection of that vector over the trajectory, and
2:27 then you only care about that.
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Parinaz Naseri.