EE 2115-01 - Lec 28 - 2026_11_02
Overview
Hiren Trada reviews the midterm topics, then explains Zener diode biasing, voltage clamping, and clipper circuits before introducing comparator behavior and configurations. Examples show a 5 V Zener clipping positive inputs above its threshold, opposite-facing 5 V Zeners clamping at about ±5.7 V, and comparator outputs switching between their supply rails according to which input is greater.
Key takeaways
- A reverse-biased 5 V Zener clamps its output near 5 V once it conducts, while a series resistor absorbs the excess input voltage.
- With a 100-ohm series resistor and a 6 V input, a 5 V Zener circuit has 1 V across the resistor and carries 10 mA in the simplified model.
- A single Zener can clip a positive waveform near 5 V in reverse bias and clamp the opposite polarity near 0.7 V in forward bias.
- Two opposite-facing 5 V Zeners conduct as one forward diode and one reverse Zener, creating an approximate clamp threshold of 5.7 V in either direction.
- A comparator switches to the positive rail when Vin+ exceeds Vin− and to the negative rail when Vin− exceeds Vin+.
- A comparator is non-inverting when the varying signal is applied to its plus input and inverting when the signal is applied to its minus input; this choice reverses which signal polarity produces a high output.
Chapters
- The midterm will cover three topics: Zener diodes, comparators, and op amps.
- Hiren Trada had not yet decided whether the exam would use one integrated question or two separate questions.
- A Canvas poll may check how many students will be out of town for a Friday conference.
- A Zener diode behaves like a regular diode in forward bias, turning on at approximately 0.7 V.
- In reverse bias, it conducts after reaching its designed breakdown voltage, called the Zener voltage VZ.
- Available Zener voltages range from about 2 V to 200 V, so a 5 V part can be selected for a 5 V clamp.
- Check diode polarity first: anode above cathode is forward bias, while cathode above anode is reverse bias.
- Once a reverse-biased Zener is on, it holds approximately VZ across itself while series resistance RS drops the remaining input voltage.
- Kirchhoff's voltage law gives Vin = VRS + VZ; for a 5 V Zener, the input must exceed 5 V plus the resistor drop to maintain conduction.
- When the Zener is off, it can be treated as disconnected and the output across it follows Vin.
- For RS = 100 ohms and VZ = 5 V, inputs from 3 V through 5 V leave the Zener off, so Vout equals Vin.
- At Vin = 6 V, the resistor drops 1 V and Ohm's law gives I = 1 V / 100 ohms = 10 mA.
- In the simplified class analysis, the same current flows through the supply, resistor, and Zener.
- Below the Zener's reverse-breakdown threshold, Vout tracks the input waveform.
- When the input rises high enough to turn on the 5 V Zener, the output is held near 5 V and the waveform's positive peaks are clipped.
- The resulting circuit is a clipper, and the same reasoning applies to sine, square, or triangular inputs.
- When the input polarity reverses, the Zener is forward biased and behaves like an ordinary diode.
- After the negative-going input reaches the forward turn-on level, the output across the diode is approximately 0.7 V.
- The series resistor takes the remaining voltage, such as 0.3 V for a 1 V input or 9.3 V for a 10 V input in the simplified example.
- With two Zeners facing opposite directions, one diode is forward biased while the other is reverse biased for either input polarity.
- For 5 V Zeners, the approximate turn-on magnitude is 0.7 V + 5 V = 5.7 V.
- Ignoring the series resistor drop, inputs above 5.7 V produce an output near 5.7 V; reversing the input gives a corresponding negative clamp.
- A real diode's forward voltage rises slightly with current, so an LTspice transfer characteristic may curve from 5.7 V to about 5.71 V or 5.72 V.
- A comparator has a non-inverting plus input, an inverting minus input, positive and negative supply rails, and an output.
- Supply labels vary: positive and negative rails may also be written as VDD and VSS, VCC and VEE, or similar notation.
- The positive rail is above zero; the negative rail is zero for a single-supply circuit or below zero for a dual-supply circuit.
- The comparator output switches to one of its supply rails rather than producing an intermediate analog value.
- If Vin+ is greater than Vin−, the comparator output goes to the positive rail; if Vin− is greater than Vin+, it goes to the negative rail.
- One comparator input is treated as the reference, while the other receives the varying signal.
- Applying the signal to the plus terminal makes the circuit non-inverting; applying it to the minus terminal makes it inverting.
- The basic comparison rule stays the same in either configuration; the input connection determines which signal polarity produces a high output.
- In an inverting example with the plus input grounded, a positive-going sine wave at the minus input makes Vin− greater than Vin+, driving the output low.
- In a non-inverting example, a triangular signal at the plus input is compared with a 5 V DC reference at the minus input.
- For the non-inverting circuit, signal voltage above 5 V drives the output high, while voltage below 5 V drives it to the negative rail.
- For the inverting circuit, the same signal-versus-reference comparison produces the opposite output state.
Transcript excerpt
0:00 Boom. So, review of what's going to be on the midterm. Three major topics: Zener diode, comparators, and op amps. And uh I haven't yet decided what the questions are going to be. Um it could be one big question, not big, one question that incorporates everything, or it could be split in two. Um let's Also, there were several students who had um who had contacted me stating that they were out of town this weekend, like Friday, for a conference. So, I might uh put a poll up on the Canvas website
0:49 just to see how many people are going to be out of town. Okay. Uh uh First up, Zener diode. >> Zener diodes are special purpose diodes
2:29 that operate in reverse bias. The easiest way to think of these diodes is that they conduct in both directions, forward and reverse bias. So, forward bias is when we when you have the anode higher than the cathode, that's forward bias. If cathode is higher than the anode, then it's reverse bias. So, Zener diodes operate in both forward bias or forward mode and reverse. Okay? The only difference is that in the
3:16 forward mode it requires 0.7 volts to turn on. In the reverse mode we can design uh what that voltage would be. Okay? So, the characteristic of a Zener diode looks like this. V and I. So, in forward bias, it's going to look and then
4:13 Okay? Approximately equal to 0.7 volts. And in reverse bias There is a slope, but the slope is near vertical. I mean, the slope is far steeper than in forward bias, so it's near vertical. So, in forward bias, we say this is a
5:03 turn-on voltage. In reverse bias, it is the breakdown voltage, but if you wish to analyze it,
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Hiren Trada.