ECE 1230 F26 U3 L5 Phasor Domain Analysis Examples 2
Overview
Angela Rasmussen reviews phasor-domain circuit analysis through two worked examples: a Thevenin equivalent with a 12 V source at 10^4 rad/s, and a nodal-analysis circuit driven at 377 rad/s. She emphasizes how to convert reactive elements and sinusoidal sources, form KCL equations, distinguish Vth from Zth procedures, and apply superposition correctly when sources have different frequencies.
Key takeaways
- At ω = 10^4 rad/s, a 3 mH inductor has impedance j3 Ω and a 50 μF capacitor has impedance -j2 Ω; frequency-specific impedance conversion should precede phasor circuit analysis.
- For a Thevenin voltage, remove the load and keep sources active; for Thevenin impedance, suppress independent sources while retaining dependent sources.
- Nodal analysis requires a chosen ground, labeled node voltages, assigned branch-current directions, and one KCL equation per unknown extraordinary node.
- Same-frequency sinusoidal responses can be added as phasors, but different-frequency responses must be converted to time-domain expressions and kept at their respective frequencies.
- The 377-rad/s example converts 10 mH to j10 Ω and 20/377 μF to -j50 Ω, yielding an inductor current of about 64 mA∠-37.7°.
Chapters
- A quiz on S-domain analysis is expected to be published that day and is due Friday.
- The upcoming S-domain method replaces the known angular frequency with s = jω, allowing analysis without specifying a single frequency.
- The lecture first reinforces phasor-domain circuit analysis before moving to S-domain techniques.
- For an inductor, impedance has a positive imaginary component, jωL.
- For a capacitor, impedance has a negative imaginary component, 1/(jωC).
- The impedance poll's correct choice is A, based on the required imaginary signs and values.
- The task is to find the Thevenin equivalent seen between terminals C and D.
- Find Vth by removing the load and calculating the open-circuit voltage across C-D.
- Find Zth by suppressing independent sources and calculating the equivalent impedance looking into C-D.
- The source 12e^(j0) becomes a 12 V phasor, and resistors remain unchanged.
- At ω = 10^4 rad/s, each 3 mH inductor becomes j3 Ω.
- A 50 μF capacitor becomes -j2 Ω at the same angular frequency.
- For nodal analysis, choose ground, label the extraordinary nodes V1 and V2, and assign current directions.
- The source-connected branch current is expressed using the 12 V source and V1 across a 3 Ω resistor.
- Between V1 and V2, the 3 Ω inductive branches are represented with their phasor impedances; currents to ground use V2/3 Ω.
- At V1, three connected branches produce a KCL equation balancing the source branch against the branches leading to V2.
- At V2, four branches produce a second KCL equation, including two 3 Ω paths to ground.
- Rasmussen uses MATLAB to solve the simultaneous complex equations and identifies V2 as Vth.
- The solved open-circuit voltage is approximately 3.33∠33.7° V.
- Using the original angular frequency, the corresponding cosine signal is approximately 3.33 cos(10^4t + 33.7°) V.
- A phasor's magnitude gives the sinusoid amplitude, while its angle supplies the cosine phase shift.
- For Zth, the independent voltage source is replaced by a wire, while the load remains removed.
- The circuit is reduced by combining parallel paths and series impedances, including the inductive and capacitive branches.
- The resulting equivalent is interpreted as a resistor in series with a capacitive reactance, with an approximate capacitance of 43 μF at 10^4 rad/s.
- To calculate Vth, remove the load but keep independent and dependent sources active, then find the voltage across the labeled terminals.
- To calculate Zth, suppress independent sources only; dependent sources must remain in the circuit.
- Check terminal polarity, units, and signs; a negative real resistance in this passive example signals an error to investigate.
- For multiple independent sources, activate one source at a time and suppress the others, then combine their contributions.
- Sources at the same angular frequency can be combined as phasors after converting them to the same frequency-domain circuit.
- For different frequencies, solve each frequency separately, convert each response to the time domain, and retain its own frequency.
- The second exercise asks for the inductor current in a circuit driven at 377 rad/s.
- A 20 Ω resistor remains resistive, while a 10 mH inductor becomes j10 Ω.
- The 20/377 μF capacitor becomes -j50 Ω, and the 4 sin(377t) V source is converted to a cosine-reference phasor of 4∠-90°, or -4j V.
- The circuit is grounded and labeled with node voltage Vx; branch-current directions are chosen before writing KCL.
- The resistor branch current is (Vx - 12)/20, and the inductor branch current is Vx/(10j).
- The capacitor/source branch is written using the combined impedance 30 - 50j Ω and the source contribution; all three branch currents are included in KCL.
- MATLAB is used to solve the complex node equation and convert the result to polar form.
- The inductor current is approximately 64 mA∠-37.7°.
- With the original 377 rad/s frequency, the time-domain current is approximately 64 mA cos(377t - 37.7°).
- A cellular receiver may pick up a desired carrier along with out-of-band interference from other transmitters.
- Voice information contains multiple frequency components, while Wi-Fi and aircraft communications operate on other designated frequencies.
- For different-frequency sources, reactive-element impedances must be recalculated at each source's frequency before applying superposition.
- A poll reinforces that different-frequency sources must each be analyzed as AC sources; reactive elements are not simply replaced by open circuits.
- Rasmussen says exam questions will generally emphasize setting up equations, with complex-number work comparable to the previous exam; MATLAB syntax is not expected to be memorized.
- LTspice repeatedly quits unexpectedly during the proposed simulation activity, so the software demonstration is postponed.
Transcript excerpt
0:00 All right, welcome. So, there will be a quiz. It's not published yet, so you may not see it on your to-do list. So, just note that it will probably be published today. Um, it will be due by Friday. It's going to be an S domain analysis and we're going to talk about the S domain analysis um is going to be our topic on Thursday. So it's it's a same techniques as we've had. The only difference is that we're going to substitute S= J omega instead of using the actual omega. So this will give us
0:47 the ability that when we don't know what the frequency is, we can do this for any signal and get an output for it. So that's the only difference. Um, so we're going to still work on, you know, the technique, making sure everybody's very comfortable with the analysis in just a phaser form and then we will be moving to that. So take a second to just review and check you know what if my omega is given what is my ZL and ZC for these specific values. It's going to take me a second just a
1:35 second to publish the or to post the poll everywhere. All right. So, the poll is now posted.
2:44 Um, which one do you know for sure it's not going to be >> B and Y? >> It's an correct. So, the inductor has to be positive and the capacitor has to be negative. So, it's not this one. Also, not D, right? Because there's no J's in there. Hopefully, you see that. So that means like yeah it's got to be imaginary also. And so hopefully doing the math right you do see that it ends up being a. So a is your answer for that one.
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, University of Utah: Professor Angela Rasmussen.