Gen Chem_Ch 9_7th_Heat Transfer
Overview
Dr. Reza Latifi explains heat transfer using energy conservation: when volume is constant and no work occurs, heat lost by one part of a system equals heat gained by its surroundings. He applies q = mcΔT to 32.5 g of aluminum at 45.8°C placed in 105.3 g of water at 15.4°C, calculating a shared final temperature of 17.3°C and showing how specific heat capacity affects each substance's temperature change.
Key takeaways
- At constant volume with no work, energy conservation requires q_system = −q_surroundings, making the signs of heat changes opposite.
- For calorimetry problems, express heat as q = mcΔT and use the same equilibrium final temperature for every substance in thermal contact.
- In the example, 32.5 g of aluminum and 105.3 g of water reach an equilibrium temperature of 17.3°C.
- The aluminum's temperature falls by 28.5°C while the water's rises by 1.9°C; their heat changes balance despite the unequal temperature changes.
- Water's specific heat, 4.18 J/(g·°C), is over four times aluminum's 0.903 J/(g·°C), so a given amount of heat changes water's temperature less.
Chapters
- The first law is expressed as ΔE = q + w, with heat calculated as q = cΔT or q = mcΔT.
- For a system and its surroundings, ΔE_system = −ΔE_surroundings; when volume does not change, w = −PΔV = 0.
- With no work, heat exchange reduces to q_system = −q_surroundings, so the negative sign must be retained.
- The example combines 32.5 g of aluminum at 45.8°C with 105.3 g of water at 15.4°C; their final temperatures are equal at equilibrium.
- Latifi uses specific heats of 0.903 J/(g·°C) for aluminum and 4.18 J/(g·°C) for water, setting q_Al = −q_water.
- Substituting q = mcΔT gives approximately 29.3ΔT_Al = −440.2ΔT_water, or ΔT_Al = −15.0ΔT_water.
- Writing both temperature changes in terms of the shared final temperature and solving yields T_final = 17.3°C.
- Water warms from 15.4°C to 17.3°C, so ΔT_water is +1.9°C and water gains heat.
- Aluminum cools from 45.8°C to 17.3°C, so ΔT_Al is −28.5°C and aluminum loses heat.
- Aluminum's larger temperature change is consistent with its specific heat of 0.903 J/(g·°C), much lower than water's 4.18 J/(g·°C).
Transcript excerpt
0:11 [music] >> Hello and welcome back and I hope until this time of the day you had a great time. And last couple of lectures I mentioned this that delta E is equal to Q plus work, heat plus work. And Q by itself it can be calculated through specific heat capacity multiplied change with the temperature or if you know the mass in that case you say mass multiply specific heat capacity multiply the change with the temperature and that's going to give [clears throat] us Q. But sometime you know instead of just focusing on the temperature of the system or calculating the mass of the system you can get heat of the reaction or the heat of the system by studying outside. And let's go after this one and and try to figure out how much you know energy we are exchanging with outside and how do we calculate for example Q. So we say delta E of the system is equal
1:00 to minus delta E of outside. So wherever I have delta E I'm going to replace it by your work plus heat or heat plus work. And next step I'm going to say if there is no change with the volume in that case work is going to be equal to zero. Why? Because work is equal to minus P delta V. And if delta V is equal to zero if there is no change with the volume then entire of the work is going to be equal to zero. So now wherever you have work work it will be canceled. And remember until now you have Q plus work for the system and this is equal to minus Q plus work for outside. And if work is equal to zero then you cancel that W and that one and now you
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Dr. Reza Latifi at Oklahoma State University, OSU.