Calculus II ep29: Interval of convergence (Nov 18, 2026)
Overview
Chris Staecker develops a practical method for finding power-series convergence: apply the ratio test to determine the interior interval, then test each endpoint separately when an interval of convergence is required. Examples include the order-zero Bessel series, a series centered at 2 with interval [1, 3), and radius-of-convergence calculations for series centered at 0, -3, and 3.
Key takeaways
- For factorial terms, simplify ratios using (n+1)! = n!(n+1); this turns factorial quotients into simple factors such as n+1 or 1/(n+1).
- A ratio-test limit of 0 for every fixed x, as in the order-zero Bessel series, means convergence for all real x and an infinite radius of convergence.
- For a series centered at a, the ratio test typically produces a condition in |x-a|; solving it gives the radius and locates the interval around a.
- The ratio test determines the open interior of a power series’ convergence interval, but boundary points require separate tests.
- For the series (x-2)^n/(n+4), the endpoints behave differently: x=1 converges by the alternating series test, while x=3 diverges by comparison with 1/n, giving [1, 3).
- If a problem asks only for radius of convergence, stop after solving the ratio-test inequality; endpoint convergence does not affect the radius.
Chapters
- Factorials multiply all positive integers up to the stated value, so (n+1)! is not n! + 1.
- Use (n+1)! = n!(n+1) to simplify the ratios (n+1)!/n! = n+1 and n!/(n+1)! = 1/(n+1).
- These cancellations are especially useful when applying the ratio test to power series with factorial coefficients.
- The example is the order-zero Bessel function series with terms involving (-1)^n x^(2n)/(2^(2n)(n!)^2).
- In the ratio test, the signs cancel, the powers leave |x|^2/4, and the factorial ratio contributes 1/(n+1)^2.
- The resulting ratio tends to 0 for every fixed x, so the series converges for all real numbers and has no finite endpoints to check.
- A power series centered at x = a uses powers of (x-a), rather than powers of x.
- The earlier examples using x^n are centered at zero; a series using (x-2)^n is centered at 2.
- The center predicts where the convergence interval is located, while the ratio test determines its radius.
- For the series with terms (x-2)^n/(n+4), the ratio test simplifies to |x-2|(n+4)/(n+5).
- As n tends to infinity, (n+4)/(n+5) tends to 1, leaving the convergence condition |x-2| < 1.
- Solving the inequality gives the open interior interval 1 < x < 3, centered at 2 with radius 1.
- At x = 1, the series becomes alternating, with terms (-1)^n/(n+4); it converges by the alternating series test.
- At x = 3, the series becomes 1/(n+4), which diverges by limit comparison with the harmonic series 1/n.
- Combining the interior and endpoint results gives the interval of convergence [1, 3).
- The interval of convergence records all x-values where a power series converges, including whether either endpoint is included.
- The radius of convergence is the distance from the center to the edge of the interval; it is 1 for the example centered at 2.
- Finding a radius does not require endpoint tests, because endpoint behavior does not change the radius.
- For a power series centered at a, a radius r separates guaranteed convergence when |x-a| < r from divergence when |x-a| > r.
- When |x-a| = r, the ratio test does not settle convergence, so each boundary point must be tested separately.
- The examples also illustrate exceptional radii: the Bessel series has infinite radius, while radius zero is possible in principle.
- For the series with terms 2^n x^n/√n, the ratio-test limit is 2|x|, so convergence requires |x| < 1/2 and the radius is 1/2.
- The powers (x+3)^n identify the center of the next example as -3, since x+3 = x-(-3).
- For terms proportional to n(x+3)^n/4^n, the ratio test gives |x+3|/4 < 1, so the radius is 4.
- The practice problem required correcting a board-writing error so the expression was a power series in (x-3)^n.
- The ratio test leaves a factor |x-3|/6; the remaining n-dependent ratio tends to 1.
- Solving |x-3|/6 < 1 gives radius 6, and endpoint checks are unnecessary when only the radius is requested.
Transcript excerpt
0:00 All right. Let'11 discuss some more about power series convergence. That's what we've been talking about the past couple times. Um if I show you a power series, can you tell me for which x does the series converge? That's what we have been discussing. Um I had just a couple more examples. We did some kind of standard examples last time. It can get slightly more complicated in in in a couple different ways. Not such a big deal, but uh a few more things to discuss. First of all, um I would like to say power series often and we will see this going forward a lot. Power series often involve factorials.
0:51 So let's talk briefly about factorials. This is uh factorial is written like this with a little exclamation six. Six This is pronounced six factorial. Anybody seen this before? You know what this means? >> Zero factorial. >> Yeah, this is the product of all the numbers up to six. 6 * 5 * 4 * 3 * 2 * 1 or you can write it the other way, of course, 1 * 2 * 3 all the way up to six. That's what that means. All right? This is a fairly big number and if you, you know, like 100 factorial is super big. You multiply together all the numbers up to 100. All right? It turns out for reasons that we'll see eventually, um
1:38 many actually like most useful power series that we're going to encounter involve factorials inside the summation. Uh and for this reason or I'm we're about to do an example, but we will see uh So let me just say n factorial often appears inside the series appears in the series. And because of that um if you want to do the ratio test,
This is the start of the transcript. Save this video free for the whole transcript, searchable and time-coded.
In this course
Related notes
Summary, takeaways, and chapters were generated by AI from the video's transcript and may contain errors. The video belongs to its creator, Prof Staecker.